About
All Feedback (929)
- twisterscrews (10280)- Feedback left by buyer.More than a year agoVerified purchaseGood buyer, prompt payment, valued customer, highly recommended.
- suntekstore_uk (338206)- Feedback left by buyer.More than a year agoVerified purchaseGood buyer, prompt payment, valued customer, highly recommended.
- vintagehardwareworld (7640)- Feedback left by buyer.More than a year agoVerified purchaseGood buyer, prompt payment, valued customer, highly recommended.
- remi-tools-ltd (152418)- Feedback left by buyer.More than a year agoVerified purchaseGood buyer, prompt payment, valued customer, highly recommended.
- cleaners4hygiene (12183)- Feedback left by buyer.More than a year agoVerified purchasePrompt Payment Valued Customer thanks 4 shopping @ Cleaners4hygiene A++++++
- wonderland_2020 (9220)- Feedback left by buyer.Past monthVerified purchaseHope to deal with you again. Thank you.
Reviews (12)
01 May, 2018
Fitting to a Umarex MP5K (CO2) BB
Yep. Just bought one. Exactly how I thought it would be: Splits into two halves with small hex head bolts and nuts. All you have to do is do a bit of dismantling!
1/. Take out retaining pin that holds foregrip.
2/. Remove forward sight.
3/. Remove foregrip.
4/. Place retaining pin in hole of the left hand side handgrip then place against the MP5.
5/. Bring right hand side of the handgrip to the MP5 and match up hole where retaining pin will be.
6/. Be patient and take time and persevere to get the retaining pin located through the holes......
7/. Once on its located correctly, slightly compress the two halves together while you add one bolt at a time. Remember not to tighten them all fully, just a little turn at a time then move to the next. Then repeat procedure until all bolts feel firm and all mating surfaces are flush.
8/. Handguard is now complete on the Umarex H&K MP5k (CO2) BB version.
9/. All you need do, now, is to look for a nice foregrip that fits on the handguard lower rail.
10/. Where the blowback feature is on this model you may need to cut away a little on the handguard to allow full return. An easy job, but only if you feel it necessary.
02 Oct, 2022
Elegantly understated.
We have owned and used, daily, a Melitta Look (with glass Jug) for two or three years. We have loved it. But, what with rising energy costs I was concerned about the hot plate consumption for brew time and the length of time it can stay on. Other than that, really good.
When the chance arrived to buy this beauty for just £35 I wasn't going to say no!
It really is the next step up: Sublime.
Very well thought out ergonomics and styling. Great thought gone into the 'move to the side' filter section. It pivots, with ease, to assist with the filter paper we use and loading/unloading coffee. All one handed.
Great idea for the water tank. It can be removed for ease of use but we leave in situ to fill with a water filter Jug as the hard water, here, is terrible.
Setting up is quite, quite simple.
The turning on to when the coffee has been brewed is a matter of no more than 3 minutes. Extremely efficient energy wise. And then, it turns off the power, almost, immediately. Even more efficiency!
The insulated stainless Jug keeps it hot. Waaaaaaay longer than the glass Jugs do. But......
We have noticed the Jug doesn't hold as much as the jug/water tank of the Look model. A difference of one mug. That's something you need to work on when changing machines to your get your brew strength/flavour right.
Also, the insulated Jug doesn't keep it hot for too long. Maybe 2 or 3 hours before the edge is taken off and then it becomes warm. Definitely cold after 12 hours.
Compared to the insulated Jug we bought from Lidl (too tall to use with Melitta machines) that can keep our coffee hot for a good 20 hours and is still warm at 24 hours. That's the only negative we would like the Melitta R&D team asses and correct.
Other than that......... BRILLIANT!
14 Apr, 2023
Simply sublime.......
Brilliant! Would definitely buy again. Great bit of kit, btw :)