PCB EN06B8 Silver Solder Glue

RC Control Freak UK (22943)
99.4% positive Feedback
Price:
£4.99
Free delivery in 2-3 days
Estimated between Tue, 6 May and Wed, 7 May
Ships today if you order in the next Ships today if you order in the next 51m 35s
Returns:
30 days return. Buyer pays for return postage. If you use an eBay delivery label, it will be deducted from your refund amount.
Condition:
New
Silver Conductive 0.2ML Electrically Paste Adhesive Paint PCB Repair. Soldering Iron in a Syringe! Dilution ratio conductive paint: thinner = 1:0.7-0.8 (weight ratio). The solution when you can't find the soldering iron, don't want to bother or your out in the woods!

About this product

Product Identifiers

BrandPCB
MPNEN06B8
UPC0799491356726
eBay Product ID (ePID)15020502243

Product Key Features

TypeSilver Solder Glue

All listings for this product

Buy it now
New

Ratings and reviews

3.8
44 product ratings
  • 26 users rated this 5 out of 5 stars
  • 2 users rated this 4 out of 5 stars
  • 6 users rated this 3 out of 5 stars
  • 2 users rated this 2 out of 5 stars
  • 8 users rated this 1 out of 5 stars

Would recommend

Good value

Good quality

Most relevant reviews

  • Most favourable review

    Kind of works

    This works but you need to give it a lot of time to dry, depending on the thickness its days to dry even a thin layer but if you accept this it actually works. I would not describe it as "glue" more like paint and its worth noting its not conductive until dry! For the price its worth a go, I had limited success repairing a track on a rotary switch worked for a little while till arcing destroyed the fix but to be fair I think I was pushing it as the current is about 3A across it which I dont think this product is suitable for. Minor small low current tracks should work ok but then you could just solder bridge them. For the price give it a go

    Verified purchase: YesCondition: New

  • Most critical review

    Needs English instructions.

    First time I've used this product. The paste wouldn't exit the hypodermic needle supplied. Increasing the pressure blew the needle off, spilling all the paste. The only text was in Chinese, so I have no idea whether or not I was using it correctly, if I had to heat it. Might be good if English instructions were included. Might be good quality, but I can't say, as I had to abandon it. Can't recommend it in its current form, without instructions.

    Verified purchase: YesCondition: New

  • Disappointed with the results.

    My assessment is based holy on what I needed the product for which wasn't delicate soldering on PCBs. So, I wouldn't recommend it because the amount of 'solder' provided is I would say minimal. The hypodermic containing the solder could hold a deal more. I bought three tubes for my task but that wasn't sufficient.....I'm now wondering if there's any other option for me as using 'hot' solder would damage the thin sheet aluminium I'm working with. I also found that to get the solder to set/harden I had to judiciously use a hot air gun....no problem but an unexpected neccessity. I've rated it 'no' for quality only because it didn't work for me. I've not compared it to other similar products. All in all, I was disappointed with the product, despite reading all the information provided online.

    Verified purchase: YesCondition: New

  • A good product for its intended use.

    Suitable for repairing PCB tracks and pads; its best to use a very small amount to ensure it sets. Not suitable for connecting wires to PCB Requires moderate heat to cure.

    Verified purchase: YesCondition: New

  • Heated rear window

    Much to my surprise this fixed a loose connection on a heated rear window. The semi-rigid feed wire wanted to pull off the connection and this product would not hold but a temporary piece of tape did the trick until the adhesive had set. Good fix and good connection: clear window.

    Verified purchase: YesCondition: New

  • Very happy - fixed my car read window demister.

    I used this conductive paste to repair my car rear window demister where one of the lines had been damaged. I used a small paint brush to paint a thin layer and let it dry overnight. It dries into a thin film and seems quite resistant to scratching. This fixed my demister. I'm very happy with this product.

    Verified purchase: YesCondition: New

  • NOT conductive in thin layers, long drying time

    I tried to fix connections on keyboard membrane. 2 of 3 connections i have managed to fix. One of them is shoving that glue is not conductive ar all. it takes more than 24 hours to completely dry and conductivity is not guaranteed. One thin layer of paste is not enough to make it conductive. when is wet is not conductive at all. i had to apply 3 layers to make conductive connection and it took 5 days to dry out completely.

    Verified purchase: YesCondition: New

  • Paint not glue

    Don’t think of this paste as a glue it is not like a glue it is more Like a paint. If you use too much it takes forever to set. I tried to use it as you would solder it is definitely no replacement for solder. Probably great for hairline cracks on a circuit board. Not not much good for anything else.

    Verified purchase: YesCondition: New

  • Excellent product

    Works well saved me from having to pay £250 for a new seat module with a worn circuit board.And no problem with heat transfer.

    Verified purchase: YesCondition: New

  • memory stick

    manage to solder the four wires together on my granddaughters memory stick after she had bent it almost at 90 degrees. 6 months college work had been saved as she had not backed it up. SAVED THE DAY GREAT STUFF.

    Verified purchase: YesCondition: New